Weld From Bottle Plastic Adhesive Set XXL

Description

Weld From Bottle Plastic Adhesive Set XXL
The description of this item has been automatically translated. If you have any questions, please feel free to contact us.
Weld seam from the bottle of plastic adhesive set XXL
✔ Sticks bombproof in seconds
✔ Industrial adhesive can also be used without granules
✔ Shelf life 1-2 years
✔ Content: 20g/40g = approx. 240cm chemical weld
✔ including primer for plastics that are difficult to bond (e.g. PE, PP, silicone)
✔ including cleaner/adhesive remover
description
designation
: Plastic Adhesive Set II
contents
: 1x industrial adhesive 20g, 1x granulate 40g, 1x HG primer 15ml, 1x HG cleaner 20g
function
: Extremely efficient adhesive repair kit especially for plastic
item number
: S10002
Firmly bond problematic plastic materials
Oily plastics such as polyethylene, polypropylene, silicone or Teflon are extremely difficult materials to bond. If these materials are bonded without the primer pre-treatment, only slight adhesion is achieved, but no proper bonding. The primer included in this set enables you to permanently bond even plastics that are difficult to bond.
This is how our adhesion promoter works
As an adhesion promoter, the HG primer creates a chemical bond between two immiscible substances. This makes the breaking point more receptive to permanent adhesion. The substance improves the adhesion properties of surfaces immensely and makes them easier to wet.
The application of the plastic glue set
1. CLEAN & RUFFLE THE SURFACE
The weld seam from the bottle can only develop its full adhesive strength if the breaking point is prepared accordingly. Ideally, the surface should be roughened up with sandpaper/wire brush and any dirt removed. There must be no dust, rust, grease or glue residue and the adhesive surface must be completely dry. A thin layer of primer is then brushed directly onto the fracture site. (Primer evaporates in a few seconds)
2. RIP UP GRANULES
The objects to be glued are then joined together exactly at the break point and a fine layer of granulate is applied. The powder height must not be more than 2mm. No chemical reaction occurs before adding the industrial adhesive.
3. APPLY INDUSTRIAL ADHESIVE
Now the industrial adhesive from the second bottle is carefully dripped onto the granules until all the granules are soaked in adhesive. As soon as the two components come into contact, a chemical reaction occurs and heat is generated. We always recommend welding both sides of the break point for maximum strength. The more often the gluing process is repeated, the more stable the connection will be.
4. ALLOW COMPOUND TO CURE
After just a few seconds, the weld seam from the bottle achieves its full adhesive strength. Then, when the chemical reaction is over, the seam can be sanded, drilled or even painted immediately. Depending on the materials, the final strength of the breaking point can vary.
Danger notices plastic adhesive
Attention
GHS07
ethyl 2-cyanoacrylate
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H335 May cause respiratory irritation.
Hazard Statements Primer
DANGER
H225 Highly flammable liquid and vapour.
H304 May be fatal if swallowed and enters airways.
H315 Causes skin irritation.
H336 May cause drowsiness and dizziness.
H410 - Very toxic for water organisms with long-term effect.
Hazard warnings Cleaner
DANGER
H225 Highly flammable liquid and vapour.
H319 Causes serious eye irritation.
H336 May cause drowsiness and dizziness.
The weld seam from the bottle can only develop its full adhesive strength if the breaking point is prepared accordingly. Ideally, the surface should be roughened up with sandpaper/wire brush and any dirt removed. There must be no dust, rust, grease or glue residue and the adhesive surface must be completely dry. A thin layer of primer is then brushed directly onto the fracture site. (Primer evaporates in a few seconds) Now the industrial adhesive from the second bottle is carefully dripped onto the granules until all the granules are soaked in adhesive. As soon as the two components come into contact, a chemical reaction occurs and heat is generated. We always recommend welding both sides of the break point for maximum strength. The more often the gluing process is repeated, the more s
Marke
HG Power Glue
EAN
4250740801382
Herstellernummer
HG-Kunststoffset XXL
Geeignet für
Universal
Herstellungsland und -region
Deutschland
Produktart
Alleskleber